AD5320 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

AD5320

+2.7 V to +5.5 V, 140
A, Rail-to-Rail Output 12-Bit DAC in a SOT-23

Analog Devices 

AD5320

GENERAL DESCRIPTION

D/A Section

The AD5320 DAC is fabricated on a CMOS process. The

architecture consists of a string DAC followed by an output

buffer amplifier. Since there is no reference input pin, the

power supply (VDD) acts as the reference. Figure 20 shows a

block diagram of the DAC architecture.

VDD

DAC REGISTER

REF (+)

RESISTOR

STRING

REF (–)

VOUT

OUTPUT

AMPLIFIER

GND

Figure 20. DAC Architecture

Since the input coding to the DAC is straight binary, the ideal

output voltage is given by:

V OUT

= V DD

×





D

4096





where D = decimal equivalent of the binary code that is loaded

to the DAC register; it can range from 0 to 4095.

R

R

R

TO OUTPUT

AMPLIFIER

R

R

Figure 21. Resistor String

Resistor String

The resistor string section is shown in Figure 21. It is simply a

string of resistors, each of value R. The code loaded to the DAC

register determines at which node on the string the voltage is

tapped off to be fed into the output amplifier. The voltage is

tapped off by closing one of the switches connecting the string

to the amplifier. Because it is a string of resistors, it is guaran-

teed monotonic.

Output Amplifier

The output buffer amplifier is capable of generating rail-to-rail

voltages on its output which gives an output range of 0 V to

VDD. It is capable of driving a load of 2 kΩ in parallel with

1000 pF to GND. The source and sink capabilities of the out-

put amplifier can be seen in Figures 8 and 9. The slew rate is

1 V/µs with a half-scale settling time of 8 µs with the output

unloaded.

SERIAL INTERFACE

The AD5320 has a three-wire serial interface (SYNC,

SCLK and DIN), which is compatible with SPI, QSPI and

MICROWIRE interface standards as well as most DSPs. See

Figure 1 for a timing diagram of a typical write sequence.

The write sequence begins by bringing the SYNC line low. Data

from the DIN line is clocked into the 16-bit shift register on the

falling edge of SCLK. The serial clock frequency can be as high

as 30 MHz, making the AD5320 compatible with high speed

DSPs. On the sixteenth falling clock edge, the last data bit is

clocked in and the programmed function is executed (i.e., a

change in DAC register contents and/or a change in the mode of

operation). At this stage, the SYNC line may be kept low or be

brought high. In either case, it must be brought high for a mini-

mum of 33 ns before the next write sequence so that a falling

edge of SYNC can initiate the next write sequence. Since the

SYNC buffer draws more current when VIN = 2.4 V than it does

when VIN = 0.8 V, SYNC should be idled low between write

sequences for even lower power operation of the part. As is

mentioned above, however, it must be brought high again just

before the next write sequence.

Input Shift Register

The input shift register is 16 bits wide (see Figure 22). The first

two bits are “don’t cares.” The next two are control bits that

control which mode of operation the part is in (normal mode or

any one of three power-down modes). There is a more complete

description of the various modes in the Power-Down Modes

section. The next twelve bits are the data bits. These are trans-

ferred to the DAC register on the sixteenth falling edge of SCLK.

DB15 (MSB)

DB0 (LSB)

X

X

PD1 PD0 D11 D10 D9

D8

D7

D6

D5

D4

D3

D2

D1

D0

DATA BITS

0 0 NORMAL OPERATION

0 1 1k⍀ TO GND

1 0 100k⍀ TO GND POWER-DOWN MODES

1 1 THREE-STATE

Figure 22. Input Register Contents

–8–

REV. B

Share Link: