DMS-20PC 查看數據表（PDF） - Murata Power Solutions

零件编号

产品描述 (功能)

生产厂家

DMS-20PC

3½ Digit, LED Display, Low-Cost, Subminiature Digital Panel Voltmeters

Murata Power Solutions 

4. DISPLAY TEST/HOLD (Pin 9) Function: Pin 9 is a dual-function

pin. On all standard models (without "-H" suffix), tying pin 9 to pin 1

(+5V SUPPLY) activates the meter's DISPLAY TEST feature. All display

segments, except the decimal points, will be illuminated. The display

will show "1888" ("–1888" if a negative input signal is present). Do

not leave the meter in the test mode for more than 10 seconds as

this will cause the meter's operating temperature to rise and possibly

affect its performance. Pin 9 must be left open when the test function

is not being used.

On models with the "-H" suffix (DMS-20PC-1-RS-H for example), pin

9 serves as a DISPLAY HOLD control pin. Tying pin 9 to +5V SUPPLY

(pin 1) on these models will hold or "freeze" the current display read-

ing indefinitely. Pin 9 must also be left open when the hold function is

not being used. After disabling DISPLAY HOLD, allow the meter a full

10 seconds to resume normal calibrated operation before holding a

new reading.

The DISPLAY TEST or DISPLAY HOLD pin should normally be con-

nected, via a selector switch, to pin 1 (+5V SUPPLY). If automatic,

logic-controlled operation is desired, only PNP or MOSFET transis-

tors should be used. The base or gate of these transistors should be

driven sufficiently hard to bring pin 9 within 0.05V of +5V SUPPLY.

5. DISPLAY ENABLE (Pin 2) Function: On all models, tying pin 2 to

pin 1 (+5V SUPPLY) applies full power to the LED display. This is the

normal mode of operating the meter. Leaving DISPLAY ENABLE open

(no connection), only turns off the LED display. The meter's analog-

to-digital converter continues to sample the input signal. Total current

consumption with the display off is approximately 400μA (0.4mA).

This is a very useful feature if the meter is used in battery-powered

equipment.

With the exception of the low-power red LED models (DMS-20PC-X-

RL), a regulated voltage lower than +5V SUPPLY can be used to dim

the display intensity. Display intensity control is best performed with

the high brightness, red LED, DMS-20PC-X-RH model. All low-power

red LED models must have DISPLAY ENABLE tied directly to pin 1

(+5V SUPPLY). Voltages applied to DISPLAY ENABLE must never be

greater than +5V SUPPLY.

6. Gain Adjust: There is a gain-adjust potentiometer on the back of

each meter. It has approximately ±50 counts (±2.5%) range of

adjustment. Since these devices essentially have no zero/offset

errors, a gain adjustment is effectively an overall accuracy adjust-

ment. Though they may be performed at any point (except zero),

accuracy adjustments are most effective when performed with

higher level input signals. The circuit shown in Figure 10 provides

±10% range of adjustment.

7. Soldering Methods: All models in the DMS-20PC Series easily with-

stand most common wave soldering operations. We recommend,

however, that you evaluate the effects your particular soldering

techniques may have on the meter’s plastic case and high-precision

electrical performance. We recommend the use of no-clean solders.

www.murata-ps.com

DMS-20PC Series

3½ Digit, LED Display, Low-Cost, Subminiature

Digital Panel Voltmeters

8. Suggested Mating Connectors:

Panel mounted:

Connector housing

Terminal type

Crimping tool

Wire size

Insulation diameter

Stripping length

DATEL P/N 4320-01069-0

DATEL P/N 4400-01032-0

DATEL P/N 39-2099000

22 to 26 AWG

0.062" (1.57mm) maximum

0.100 to 0.125" (2.54 to 3.17mm)

Board mounted:

Socket DATEL P/N 4320-01074-0

APPLICATIONS

DMS-20PC meters are highly versatile devices that can be used in

hundreds of applications. The application circuits chosen for this section

are ones that have historically received many inquiries.

The schematic in Figure 1 shows that the meter's high-impedance input

consists of an op amp powered from a ±5Vdc power supply (the –5V is

internally generated). One can easily see why input signals applied to (–)

INPUT LO and (+) INPUT HI have to be kept within the power supply rails

of ±5V. Also note that only pin 11 has a current-limiting 909kΩ series

resistor. High input voltages that have a common ground with pin 3 (5V

RETURN) should only be applied to pin 11 ((+) INPUT HI) and never to pin

12. In these high-voltage cases, pin 12 should always be tied to pin 3

(5V RETURN).

The schematic also shows that pin 3 is the meter's zero-volt reference

point — regardless of the type of power or signal source used. This is

an important point to keep in mind when a digital or analog multimeter

is used to make system measurements. The multimeter's negative lead

(usually the black one) must be connected to pin 3 (5V RETURN).

1. Single-Ended Input Configurations: True single-ended measure-

ments can be made with any DMS-20PC meter. The circuit of Figure

2 avoids problems normally associated with ground-loop currents.

Separate ground runs should be used for 5V RETURN (pin 3) and (–)

INPUT LO (pin 12).

+

VIN

–

11

(+) IN HI

12

(–) IN LO

1

+5V SUP

DATEL

85-264Vac DMS-PS1-CM

DMS-20PC-1

8

REF OUT

2

6

DISPLAY DP1

ENABLE

7

REF IN

3

5V RET

AC to DC Converter

Figure 2. Single-Ended Input Configuration

Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000

MPM_DMS_20PC.D02 Page 3 of 6

Share Link: