HSP45116-DB 查看數據表（PDF） - Intersil

零件编号

产品描述 (功能)

生产厂家

HSP45116-DB

HSP45116 Daughter Board

Intersil 

HSP45116-DB

Getting Started

This section describes the initial evaluation system setup for

the HSP45116-DB and HSP-EVAL board set. The system

setup consists of mother/daughter board assembly, software

installation, and system test to verify proper operation of the

board set.

Assembly

The evaluation board set is assembled by mating the

HSP45116-DB daughter board with the HSP-EVAL

motherboard. This is accomplished by inserting the header

pins sticking through the bottom (solder side) of the daughter

board into the three 2 x 25 pin connectors on the

motherboard. Proper alignment requires that the J1, J2, and

J3 headers on the HSP45116-DB mate with the J1, J2, and

J3 connectors on the HSP-EVAL. A moderate amount of force

is required to seat the header pins in the motherboard

connectors.

CONFIGURATION JUMPER FIELD A

50 PIN CONTROL HEADER (J2)

CONFIGURATION JUMPER FIELD B

CONTROL

CLK

RIN0-15 16

RO0-15

16

IMIN0-15 16

HSP45116 IO0-15

16

HSP45116-DB

FIGURE 1. HSP45116-DB BLOCK DIAGRAM

As part of the initial assembly, the HSP-EVAL and HSP45116-

DB must be provided with the default jumper configuration to

ensure proper operation with the system test software. Each

board leaving the factory is supplied with the default

configuration, but the respective configurations are examined

here for completeness. The motherboard's default configuration

is realized by inserting jumpers into the HSP EVAL's J4 jumper

field as shown in Figure 2 (see the HSP-EVAL User’s Manual

for more detailed information). The default configuration for the

HSP45116-DB requires jumper placement across the

Configuration Jumper Fields A and B and the J3 Control

Header as shown in Table 1.

Before using the board set with the supplied software, power

must be supplied to the boards, and the HSP-EVAL must be

connected to the parallel port of the target PC. Power is

provided to the boards by connecting the VCC and GND pins of

the J6 header on the HSP-EVAL to a standard 5V ±5% supply.

As an alternative, power may be supplied through the HSP-

EVAL’s 96-Pin DIN connectors. The HSP-EVAL is connected to

the target PC by connecting the HSP-EVAL’s 26-PIN shrouded

header to the PC’s parallel port using the supplied ribbon cable.

System Requirements for the Evaluation Board Soft-

ware

The PC system targeted to run the HSP45116-DB software

(NCOM-SOFT) and interface with the evaluation board set

must meet the following requirements:

- IBM PC/XT/AT, PS/2, or 100% compatible with a minimum

of 640K of random access memory (RAM) (NCOM-SOFT

does not require extended memory)

- At least 200kB of free disk space on your hard disk

- DOS Version 3.0 or higher

- One parallel port with 27 Pin D-Sub connector

Software Installation

The distribution diskette contains a program called

INSTALL.EXE which installs the NCOM-SOFT software onto

the target hard disk. Note: The steps in this section assume

you are installing NCOM-SOFT from a diskette in drive A:

onto a hard drive C:. If a different configuration is used,

substitute the letter of the drive where the diskette is

located for drive A;. Substitute the letter for the hard drive

for drive C:

EXT_CLK

OSC_CL

CTL0

OE_BUS1

OE_BUS2

OE_BUS3

OECTLLO

OECTLHI

ADDR0

ADDR1

ADDR2

ADDR3

ADDR4

ADDR5

ADDR6

ADDR7

STAT0

STAT1

STAT2

STAT3

PCRD0

PCRD1

SR_RD

N.C.

N.C.

CLOCK SELECT

JUMPERS

OUTPUT ENABLE

JUMPERS

BOARD ADDRESS

JUMPERS

OUTPUT SELECT

JUMPERS

FIGURE 2. CONFIGURATION JUMPER FIELD J4

2

Share Link: