TDA8947J 查看數據表（PDF） - NXP Semiconductors.
零件编号
产品描述 (功能)
生产厂家
TDA8947J Datasheet PDF : 24 Pages
| |||
Philips Semiconductors
TDA8947J
4-channel audio amplifier
11. Static characteristics
Table 8: Static characteristics
VCC = 18 V; Tamb = 25 °C; RL = 8 Ω; VMODE1 = VCC; VMODE2 = VCC; Vi = 0 V; measured in test circuit Figure 12; unless
otherwise specified.
Symbol
Parameter
Conditions
Min
Typ Max
Unit
Supply
VCC
supply voltage
operating
no (clipping) signal
[1] 9
[2] -
18
26
V
-
28
V
Iq
Istb
Output pins
quiescent supply current
standby supply current
RL = ∞
[3] -
100 145
mA
-
-
10
µA
VO
DC output voltage
∆VOUT
differential output voltage offset
Mode selection pins
BTL mode
[4] -
[5] -
9
-
V
-
170
mV
VMODE1
selection voltage on pin
MODE1
On mode
Mute mode
Standby mode
VCC − 2.0 -
4.5
-
0
-
VCC
V
VCC − 3.5 V
0.8
V
VMODE2
IMODE1
IMODE2
selection voltage on pin
MODE2
On mode: channels 3 and 4
Mute mode: channels 3 and 4
selection current on pin MODE1 0 V < VMODE1 < (VCC − 3.5 V)
selection current on pin MODE2 0 V < VMODE2 < (VCC − 3.5 V)
[6] VCC − 2.0 -
0
-
-
-
-
-
VCC
V
VCC − 3.5 V
20
µA
20
µA
[1] A minimum load is required at supply voltages of VCC > 22 V: RL = 3 Ω for SE and RL = 6 Ω for BTL.
[2] The amplifier can deliver output power with non clipping output signals into nominal loads as long as the ratings of the IC are not
exceeded.
[3] With a load connected at the outputs the quiescent current will increase.
[4] The DC output voltage, with respect to ground, is approximately 0.5VCC.
[5] ∆VOUT = |VOUT+ − VOUT-|
[6] Channels 3 and 4 can only be set to Mute or On mode by MODE2 when VMODE1 > VCC − 2.0 V.
12. Dynamic characteristics
Table 9: Dynamic characteristics SE
VCC = 18 V; Tamb = 25 °C; RL = 4 Ω; f = 1 kHz; VMODE1 = VCC; VMODE2 = VCC; measured in test circuit Figure 12; unless
otherwise specified.
Symbol Parameter
Conditions
Min
Typ
Max
Unit
Po(SE)
SE output power
THD
Gv
Zi
total harmonic distortion
voltage gain
input impedance
VCC = 18 V; see Figure 8a
THD = 10 %; RL = 4 Ω
THD = 0.5 %; RL = 4 Ω
VCC = 22 V
THD = 10 %; RL = 4 Ω
Po = 1 W
7
8.5
-
W
-
6.5
-
W
-
14
-
W
-
0.1
0.5
%
25
26
27
dB
40
60
-
kΩ
9397 750 14938
Product data sheet
Rev. 02 — 16 June 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
9 of 24
Share Link: 