RCL0612200KFKEK 查看數據表（PDF） - Vishay Semiconductors
零件编号
产品描述 (功能)
生产厂家
RCL0612200KFKEK Datasheet PDF : 9 Pages
| |||
www.vishay.com
TESTS AND REQUIREMENTS
All executed tests are carried out in accordance with the
following specifications:
EN 60115-1, generic specification
EN 60115-8 (successor of EN 140400),
sectional specification
EN 140401-802, detail specification
IEC 60068-2-xx, test methods
The parameters stated in the Test Procedures and
Requirements table are based on the required tests
and permitted limits of EN 140401-802. The table presents
only the most important tests, for the full test schedule refer
to the documents listed above. However, some additional
tests and a number of improvements against those
minimum requirements have been included.
RCL e3
Vishay Draloric
The testing also covers most of the requirements specified
by EIA/IS-703 and JIS-C-5201-1.
The tests are carried out under standard atmospheric
conditions in accordance with IEC 60068-1, 4.3, whereupon
the following values are applied:
Temperature: 15 °C to 35 °C
Relative humidity: 25 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
IEC
60068-2 (1)
TEST
METHOD
TEST
PROCEDURE
Stability for product types:
4.5
4.8
4.25.1
4.25.3
4.24
4.37
4.23
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
4.23.7
-
4.19
-
Resistance
-
Temperature
coefficient
-
Endurance at 70 °C
-
78 (Cab)
67 (Cy)
-
2 (Bb)
30 (Db)
1 (Ab)
13 (M)
Endurance at
upper category
temperature
Damp heat,
steady state
Damp heat,
steady state,
accelerated
Climatic sequence:
dry heat
damp heat, cyclic
cold
low air pressure
30 (Db) damp heat, cyclic
-
1 (Aa)
14 (Na)
DC load
Cold
Rapid change of
temperature
RCL e3
-
(20 / -55 / 20) °C and
(20 / 155 / 20) °C
U = P70 x R or U = Umax.;
whichever is the less severe;
1.5 h on; 0.5 h off
70 °C; 1000 h
70 °C; 8000 h
155 °C, 1000 h
(40 ± 2) °C; 56 days;
(93 ± 3) % RH;
(85 ± 2) °C; (85 ± 5) % RH;
U = 0.1 x P70 x R ≤ 100 V;
1000 h
-
125 °C; 16 h
55 °C; 24 h; ≥ 90 % RH;
1 cycle
-55 °C; 2 h
8.5 kPa; 2 h; (25 ± 10) °C
55 °C; 24 h;
≥ 90 % RH;
5 cycles
U = P70 x R ≤ Umax.; 1 min
-55 °C; 2 h
30 min at -55 °C and
30 min at 125 °C;
1000 cycles
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR)
STABILITY CLASS 1
OR BETTER
STABILITY CLASS 2
OR BETTER
1 Ω to 2.2 MΩ
±1%
±5%
± 100 ppm/K
± 200 ppm/K
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (4 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (0.25 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
Revision: 12-Jul-17
6
Document Number: 20046
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: 