AD7452_15 查看數據表（PDF） - Analog Devices
零件编号
产品描述 (功能)
生产厂家
AD7452_15 Datasheet PDF : 24 Pages
| |||
AD7452
TYPICAL CONNECTION DIAGRAM
Figure 21 shows a typical connection diagram for the AD7452
for both 5 V and 3 V supplies. In this setup, the GND pin is
connected to the analog ground plane of the system. The VREF
pin is connected to either a 2.5 V or a 2 V decoupled reference
source, depending on the power supply, to set up the analog
input range. The common-mode voltage has to be set up
externally and is the value on which the two inputs are centered.
The conversion result is output in a 16-bit word with four
leading zeros followed by the MSB of the 12-bit result. For more
details on driving the differential inputs and setting up the
common mode, refer to the Driving Differential Inputs section.
0.1F
10F
3V/5V
SUPPLY
VREF
p-p
VREF
p-p
CM*
VDD
VIN+
CM*
VIN–
VREF
AD7452
SERIAL
INTERFACE
SCLK
SDATA
CS
GND
C/P
0.1F
2V/2.5V
VREF
*CM IS THE COMMON-MODE VOLTAGE.
Figure 21. Typical Connection Diagram
ANALOG INPUT
The analog input of the AD7452 is fully differential. Differential
signals have a number of benefits over single-ended signals,
including noise immunity based on the device’s common-mode
rejection, improvements in distortion performance, doubling of
the device’s available dynamic range, and flexibility in input
ranges and bias points. Figure 22 defines the fully differential
analog input of the AD7452.
COMMON-
MODE
VOLTAGE
VREF
p-p
VREF
p-p
VIN+
AD7452
VIN–
Figure 22. Differential Input Definition
The amplitude of the differential signal is the difference
between the signals applied to the VIN+ and VIN– pins (that is,
VIN+ – VIN–). VIN+ and VIN– are simultaneously driven by two
signals, each of amplitude VREF, that are 180° out of phase. The
amplitude of the differential signal is therefore –VREF to +VREF
peak-to-peak (that is, 2 ×VREF). This is true regardless of the
common mode (CM).
Data Sheet
The common mode is the average of the two signals, that is,
(VIN+ + VIN–)/2, and is therefore the voltage upon which the two
inputs are centered. This results in the span of each input being
CM ± VREF/2. This voltage has to be set up externally, and its
range varies with VREF. As the value of VREF increases, the
common-mode range decreases. When driving the inputs with
an amplifier, the actual common-mode range is determined by
the amplifier’s output voltage swing.
Figure 23 and Figure 24 show how the common-mode range
typically varies with VREF for both 5 V and 3 V power supplies.
The common mode must be in this range to guarantee the
functionality of the AD7452.
For ease of use, the common mode can be set up to equal VREF,
resulting in the differential signal being ±VREF centered on VREF.
When a conversion takes place, the common mode is rejected,
resulting in a virtually noise-free signal of amplitude, –VREF to
+VREF, corresponding to the digital codes of 0 to 4096.
4.5
4.0
3.5
3.25V
3.0
2.5
COMMON-MODE RANGE
2.0
1.5
1.75V
1.0
0.5
0
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
VREF (V)
Figure 23. Input Common-Mode Range vs. VREF
(VDD = 5 V and VREF (Max) = 3.5 V)
2.5
2V
2.0
1.5
COMMON-MODE RANGE
1.0
1V
0.5
0
0 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00
VREF (V)
Figure 24. Input Common-Mode Range vs. VREF
(VDD = 3 V and VREF (Max) = 2 V)
Rev. C | Page 14 of 24
Share Link: 