232259452006 查看數據表（PDF） - Vishay Semiconductors
零件编号
产品描述 (功能)
生产厂家
232259452006 Datasheet PDF : 20 Pages
| |||
www.vishay.com
VDRS Series
Vishay BCcomponents
ELECTRICAL DATA AND ORDERING INFORMATION
MAXIMUM
CONTINUOUS
VOLTAGE
VOALTT1AGmEA
(3)
MAXIMUM
MAXIMUM
VOLTAGE MAXIMUM NON-REP.
AT
ENERGY (4) TRANSIENT
STATED (10 x 1000 μs) CURRENT (5)
CURRENT
INRP (8 x 20 μs)
NOMINAL
DISCHARGE
CURRENT (7)
IN
TYPICAL
CAPACITANCE
AT 1 kHz
T
(max.)
RMS (2) DC
(V)
(V)
(V)
VI
(V) (A)
(J)
(A)
(kA)
(pF)
(mm)
E
(mm)
SAP MATERIAL
AND ORDERING
NUMBER (1)
xy (6)
1120 5.0
20.0
400
0.10
35
6.1 3.2 ± 0.8 VDRS05C420xyE
1120 10.0
56.0
1200
0.50
85
6.1 3.2 ± 0.8 VDRS07H420xyE
420
560
680
1120 25.0
73.0
2500
1.50
165
6.6 3.4 ± 0.8 VDRS10P420xyE
1120 50.0
120.0
4500
3.00
250
6.6 3.4 ± 0.8 VDRS14T420xyE
1120 100.0 344.0
6500
3.00
510
8.1 3.7 ± 0.8 VDRS20W420ByE
1240 5.0
21.0
400
0.10
30
6.4 3.6 ± 0.8 VDRS05C460xyE
1240 10.0
63.0
1200
0.50
75
6.4 3.6 ± 0.8 VDRS07H460xyE
460
615
750
1240 25.0
82.0
2500
1.50
150
6.8 3.8 ± 0.8 VDRS10P460xyE
1240 50.0
135.0
4500
3.00
225
6.8 3.8 ± 0.8 VDRS14T460xyE
1240 100.0 360.0
6500
3.00
460
8.5 4.1 ± 0.8 VDRS20W460ByE
1355 25.0
89.0
2500
1.50
135
7.2 4.1 ± 0.8 VDRS10P510xyE
510
670
820
1355 50.0
145.0
4500
3.00
220
7.2 4.1 ± 0.8 VDRS14T510xyE
1355 100.0 376.0
6500
3.00
450
8.9 4.4 ± 0.8 VDRS20W510ByE
1500 25.0
98.0
2500
1.50
120
7.9 4.5 ± 0.8 VDRS10P550xyE
550
745
910
1500 50.0
160.0
4500
3.00
180
7.9 4.5 ± 0.8 VDRS14T550xyE
1500 100.0 408.0
6500
3.00
370
9.5 4.9 ± 0.8 VDRS20W550ByE
625
825 1000 1650 100.0 448.0
6500
3.00
320
10.1 5.3 ± 0.8 VDRS20W625ByE
680
895 1100 1815 100.0 496.0
6500
3.00
270
10.6 5.8 ± 0.8 VDRS20W680ByE
Notes
(1) The products are certified according to cULus (E332800), and VDE/IEC (40002622). See Agency Approval section for certificate download
(2) The sinusoidal voltage is assumed as the normal operating condition. If a non-sinusoidal voltage is present, type selection should be based on
multiplying the peak voltage by a factor of 0.707.
(3) The voltage measured at 1 mA meets the requirements of IEC 61051.
The tolerance on the voltage at 1 mA is ± 10 %.
(4) High energy surges are generally of longer duration. The maximum energy for one pulse of 10 x 1000 μs is given as a reference for longer
duration pulses. This pulse can be characterized by peak current (Ip) and pulse width t2 (virtual time of half Ip value, following IEC 60060-2,
section 6 ). If Vp is the clamping voltage corresponding to Ip, the energy absorbed in the varistor is determined by the formula:
E = K x Vp x Ip x t2
where K is dependent on the value of t2 when the value of t1 is between 8 μs and 10 μs (see Peak Current as a Function of Pulse Width
drawing)
(5) A current wave of 8 x 20 μs is used as a standard for pulse current and clamping voltage ratings. The maximum non-repetitive transient current
is given for one pulse applied during the life of the component.
(6) For composition of the SAP part number:
Replace “x” by B for bulk type
Replace “y” by S for straight leads
T for tape and reel
F for straight leads with flange (bulk only)
A for tape and ammopack
G for straight leads with flange and H0 = 16 mm (tape and reel/ammo)
H for straight leads with flange and H0 = 18.25 mm (tape and reel/ammo)
K for kinked leads (bulk only)
L for kinked leads with H0 = 16 mm (tape and reel/ammo)
M for kinked leads with H0 = 18.25 mm (tape and reel/ammo)
(7) All varistors are UL 1449 edition 4 recognized as SPD type 5 (component level) for operating temperatures up to 85 °C. The varistors may be
used in other SPD types as 2, 3, or 4 depending on the indicated IN nominal discharge current ratings. The final acceptance of the component
is dependent upon its installation and use in complete equipment submitted to underwriters laboratories Inc.
Revision: 22-Aug-2019
4
Document Number: 29081
For technical questions, contact: nlr@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: 