MC44608 查看數據表（PDF） - Motorola => Freescale

零件编号

产品描述 (功能)

生产厂家

MC44608

Few External Components Reliable and Flexible GreenLine™ Very High Voltage PWM Controller

Motorola => Freescale 

MC44608

In stand–by mode, this current can be lowered as due to

the activation of a 200µA current source:

* + * W W Ipkmax stby

1

(Rcs(k )

Rsense(

0, 2)

)

(A)

Figure 2. Current Sense

Switching Phase

200 mA

&

10

STAND–BY

START–UP

Figure 3. Demagnetization Block

Oscillator Buffer Output

RQ

DMG

S

DMG

&

> 24

>120

mmAA

+

–

50/20 mV

Idemag

Current Mirror

Demag

1

Rsense

Isense

2

Rcs

L.E.B.

Overcurrent

Comparator

+ OC

–

1V

W The current sense input consists of a filter (6k , 4pF) and

of a leading edge blanking. Thanks to that, this pin is not

sensitive to the power switch turn on noise and spikes and

practically in most applications, no filtering network is

required to sense the current.

Finally, this pin is used:

– as a protection against over currents (Isense > I)

– as a reduction of the peak current during a Pulsed Mode

switching phase.

The overcurrent propagation delay is reduced by

producing a sharp output turn off (high slew rate). This results

in an abrupt output turn off in the event of an over current and

in the majority of the pulsed mode switching sequense.

Demagnetization Section

The MC44608 demagnetization detection consists of a

comparator designed to compare the VCC winding voltage to

a reference that is typically equal to 50mV.

This reference is chosen low to increase effectiveness of

the demagnetization detection even during start–up.

A latch is incorporated to turn the demagnetization block

output into a low level as soon as a voltage less than 50 mV

is detected, and to keep it in this state until a new pulse is

generated on the output. This avoids any ringing on the input

signal which may alter the demagnetization detection.

For a higher safety, the demagnetization block output is

also directly connected to the output, which is disabled during

the demagnetization phase.

The demagnetization pin is also used for the quick,

programmable OVP. In fact, the demagnetization input

current is sensed so that the circuit output is latched off when

this current is detected as higher than 120µA.

This function can be inhibited by grounding it but in this

case, the quick and programmable OVP is also disabled.

Oscillator

The MC44608 contains a fixed frequency oscillator. It is

built around a fixed value capacitor CT succesively charged

and discharged by two distinct current sources ICH and

IDCH. The window comparator senses the CT voltage value

and activates the sources when the voltage is reaching the

2.4V/4V levels.

Figure 4. Oscillator block

DMG

from Demag

logic block

ICH

&

SCH

OSC

4V

Window

+ comp

Clock

–

2.4 V

SDCH

IDCH

CT

The complete demagnetization status DMG is used to

inhibit the recharge of the CT capacitor. Thus in case of

incomplete transformer demagnetization the next switching

cycle is postpone until the DMG signal appears. The

oscillator remains at 2.4V corresponding to the sawtooth

valley voltage. In this way the SMPS is working in the so

called SOPS mode (Self Oscillating Power Supply). In that

case the effective switching frequency is variable and no

longer depends on the oscillator timing but on the external

working conditions (Refer to DMG signal in the figure 5).

6

MOTOROLA ANALOG IC DEVICE DATA

Share Link: