BWR-5/6-3.3/7-D12 查看數據表（PDF） - DATEL Data Acquisition products
零件编号
产品描述 (功能)
生产厂家
BWR-5/6-3.3/7-D12
DATEL Data Acquisition products
BWR-5/6-3.3/7-D12 Datasheet PDF : 11 Pages
| |||
33W, DUAL OUTPUT, MIXED-VOLTAGE DC/DC CONVERTERS
BWR Models
Performance/Functional Specifications
Typical @ TA = +25°C under nominal line voltage, balanced "full-load" conditions, unless noted. ➀
Input
Input Voltage Range:
D12 Models
D24 Models
D48 Models
10-18 Volts (12V nominal)
18-36 Volts (24V nominal)
36-75 Volts (48V nominal)
Overvoltage Shutdown: ➁
D12 Models
D24 Models
D48 Models
19-23 Volts (21V nominal)
37-42 Volts (40V nominal)
77-81 Volts (79V nominal)
Start-Up Threshold: ➁
D12 Models
D24 Models
D48 Models
9-10 Volts (9.3V nominal)
16.5-18 Volts (17V nominal)
34-36 Volts (35V nominal)
Undervoltage Shutdown: ➁
D12 Models
D24 Models
D48 Models
8.5-9.6 Volts (9.3V nominal)
16-17 Volts (16.5V nominal)
32.5-35 Volts (34V nominal)
Input Current:
Normal Operating Conditions
Standby Mode:
Off, OV, UV, Thermal Shutdown
See Ordering Guide
10mA typical
Input Reflected Ripple Current:
Source Impedance
D12 Models
D24/D48 Models
<0.1Ω, no external input filtering
200mAp-p (150mAp-p typical)
250mAp-p (225mAp-p typical)
Internal Input Filter Type
Pi (0.022µF - 4.7µH - 2.46µF)
Reverse-Polarity Protection: ➁
D12 Models
D24 Models
D48 Models
1 minute duration, 6A maximum
1 minute duration, 4A maximum
1 minute duration, 2A maximum
On/Off Control (Pin 4): ➁ ➂ ➃ ➅
D12, D24 & D48 Models
On = open or 13V - +VIN, IIN = 50µA max.
Off = 0-0.8V, IIN = 1mA max.
Sync (Option, Pin 4): ➁ ➂ ➃
Input Threshold (Rising Edge Active)
Input Voltage Low
Input Voltage High
Input Resistance
Output High Voltage (100µA load)
Output Drive Current
Input/Output Pulse Width
1-2.7 Volts
0-0.9 Volts
2.8-5 Volts
35kΩ minimum
3.5-4.8 Volts
35mA
160-360nsec
Output
VOUT Accuracy
5V Output
3.3V Output
±3% maximum
±1.5% maximum
Minimum Loading Per Specification No load, see Performance Specifications
Ripple/Noise (20MHz BW) ➁ ➄
See Ordering Guide
Line/Load Regulation ➁
See Ordering Guide
Efficiency
See Ordering Guide / Efficiency Curves
Cross Regulation: ➁
5V Output (5V@0.6A, 3.3V@0.7-7A) ±6% maximum
3.3V Output (3.3V@0.7A, 5V@0.6-6A) ±0.5% maximum
Trim Range ➁
±5%
Isolation Voltage:
Input-to-Output
1500Vdc minimum
Isolation Capacitance
470pF
Isolation Resistance
100MΩ
Temperature Coefficient
±0.02%/per°C
Output (continued)
Current Limit Inception: ➁
5V @ 95% VOUT (3.3V @ 0A)
3.3V @ 98.5% VOUT (5V @ 0A)
7.6-9.0 Amps
11.3-12.7 Amps
Short Circuit Current: ➁
5V Output
3.3V Output
5 Amps average, continuous
6 Amps average, continuous
Overvoltage Protection: ➁
5V Output
3.3V Output
Magnetic feedback
6.8 volts
4.5Volts
Maximum Capacitive Loading
D12 Models 3.3V
5V
D24, D48 Models 3.3V
5V
1000µF
470µF
2000µF
1000µF
Dynamic Characteristics
Dynamic Load Response: ➁
5V (50-100% load step to 4% VOUT) 300µsec maximum
3.3V (50-100% load step to 2.5% VOUT) 300µsec maximum
Start-Up Time: ➁
VIN to VOUT
On/Off to VOUT
20msec maximum
15msec maximum
Switching Frequency
285kHz (±15kHz)
Environmental
MTBF ➆
D12 Models
D24/D48 Models
Bellcore, ground fixed, full power, +25°C
operating ambient temperature
1.3 million hours
1.67 million hours
Operating Temperature (Ambient): ➁
Without Derating:
D12 Models
D24 Models
D48 Models
With Derating
–40 to +50°C
–40 to +60°C
–40 to +68°C
To +100°C (See Derating Curves)
Case Temperature:
Maximum Operational
For Thermal Shutdown ➁
+100°C
+110°C minimum, +117°C maximum
Storage Temperature
–40 to +120°C
Physical
Dimensions
2" x 2" x 0.45" (50.8 x 50.8 x 11.43mm)
Internal Case Connection:
D12/D24 Models
D48 Models
–Input (Pin 2)
+Input (Pin 1)
Case Material
Corrosion resistant steel with
non-conductive, epoxy-based, black
enamel finish and plastic baseplate
Pin Material
Brass, solder coated
Weight:
2.7 ounces (76.5 grams)
Primary to Secondary Insulation Level
D12/D24 Models
Operational
D48 Models
Basic
➀ Balanced "full-load" is 5V @ 3.3A/3.3V @ 5A. All models are specified with external
1µF ceramic output capacitors.
➁ See Technical Notes/Graphs for details.
➂ Devices may be ordered with On/Off Control function or a Sync function.
See Part Number Suffixes and Technical Notes for details.
➃ Applying a voltage to On/Off Control (pin 4) when no input power is applied to the
converter may cause permanent damage.
➄ Output noise may be further reduced with the installation of additional external output
capacitors. See Technical Notes.
➅ On/Off control is designed to be driven with open collector or by appropriate voltage
levels. Voltages must be referenced to the input return pin (–Input).
➆ Demonstrated MTBF available on request.
3
Share Link: