18B20 查看數據表（PDF） - Maxim Integrated
零件编号
产品描述 (功能)
生产厂家
18B20 Datasheet PDF : 22 Pages
| |||
DS18B20
ORDERING INFORMATION
PART
TEMP RANGE
DS18B20
-55°C to +125°C
DS18B20+
-55°C to +125°C
DS18B20/T&R
-55°C to +125°C
DS18B20+T&R
-55°C to +125°C
DS18B20-SL/T&R
-55°C to +125°C
DS18B20-SL+T&R
-55°C to +125°C
DS18B20U
-55°C to +125°C
DS18B20U+
-55°C to +125°C
DS18B20U/T&R
-55°C to +125°C
DS18B20U+T&R
-55°C to +125°C
DS18B20Z
-55°C to +125°C
DS18B20Z+
-55°C to +125°C
DS18B20Z/T&R
-55°C to +125°C
DS18B20Z+T&R
-55°C to +125°C
PIN-PACKAGE
3 TO-92
3 TO-92
3 TO-92 (2000 Piece)
3 TO-92 (2000 Piece)
3 TO-92 (2000 Piece)*
3 TO-92 (2000 Piece)*
8 µSOP
8 µSOP
8 µSOP (3000 Piece)
8 µSOP (3000 Piece)
8 SO
8 SO
8 SO (2500 Piece)
8 SO (2500 Piece)
TOP MARK
18B20
18B20
18B20
18B20
18B20
18B20
18B20
18B20
18B20
18B20
DS18B20
DS18B20
DS18B20
DS18B20
+Denotes a lead-free package. A “+” will appear on the top mark of lead-free packages.
T&R = Tape and reel.
*TO-92 packages in tape and reel can be ordered with straight or formed leads. Choose “SL” for straight leads. Bulk TO-92 orders are straight
leads only.
PIN DESCRIPTION
PIN
SO µSOP TO-92
1, 2, 6, 2, 3, 5,
7, 8
6, 7
—
3
8
3
4
1
2
5
4
1
NAME
N.C.
VDD
DQ
GND
FUNCTION
No Connection
Optional VDD. VDD must be grounded for operation in
parasite power mode.
Data Input/Output. Open-drain 1-Wire interface pin. Also
provides power to the device when used in parasite power
mode (see the Powering the DS18B20 section.)
Ground
OVERVIEW
Figure 1 shows a block diagram of the DS18B20, and pin descriptions are given in the Pin Description
table. The 64-bit ROM stores the device’s unique serial code. The scratchpad memory contains the 2-byte
temperature register that stores the digital output from the temperature sensor. In addition, the scratchpad
provides access to the 1-byte upper and lower alarm trigger registers (TH and TL) and the 1-byte
configuration register. The configuration register allows the user to set the resolution of the temperature-
to-digital conversion to 9, 10, 11, or 12 bits. The TH, TL, and configuration registers are nonvolatile
(EEPROM), so they will retain data when the device is powered down.
The DS18B20 uses Maxim’s exclusive 1-Wire bus protocol that implements bus communication using
one control signal. The control line requires a weak pullup resistor since all devices are linked to the bus
via a 3-state or open-drain port (the DQ pin in the case of the DS18B20). In this bus system, the
microprocessor (the master device) identifies and addresses devices on the bus using each device’s unique
64-bit code. Because each device has a unique code, the number of devices that can be addressed on one
2 of 22
Share Link: 