TCDT1110 查看數據表（PDF） - Vishay Semiconductors
零件编号
产品描述 (功能)
生产厂家
TCDT1110 Datasheet PDF : 8 Pages
| |||
TCDT1110/TCDT1110G
Vishay Semiconductors
Optocoupler, Phototransistor
Output
ABSOLUTE MAXIMUM RATINGS (1)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
OUTPUT
Collector emitter voltage
VCEO
70
V
Emitter collector voltage
VECO
7
V
Collector current
IC
50
mA
Collector peak current
tp/T = 0.5, tp ≤ 10 ms
ICM
100
mA
Power dissipation
Pdiss
150
mW
Junction temperature
Tj
125
°C
COUPLER
Isolation test voltage (RMS)
t = 1 min
VISO
5300
VRMS
Total power dissipation
Ptot
250
mw
Ambient temperature range
Tamb
- 55 to + 100
°C
Storage temperature range
Tstg
- 55 to + 125
°C
Soldering temperature (2)
2 mm from case t ≤ 10 s
Tsld
260
°C
Notes
(1) Tamb = 25 °C unless otherwise specified. Stresses in excess of the absolute maximum ratings can cause permanent damage to the device.
Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this
document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability.
(2) Refer to wave profile for soldering conditions for through hole devices.
ELECTRICAL CHARACTERISTICS
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
INPUT
Forward voltage
Junction capacitance
OUTPUT
IF = 50 mA
VF
VR = 0, f = 1 MHz
Cj
1.2
1.5
V
50
pF
Collector emitter voltage
Emitter collector voltage
Collector-emitter cut-off current
COUPLER
IC = 1 mA
IE = 100 µA
VCE = 30 V, IF = 0
VCEO
70
VECO
7
ICEO
V
V
150
nA
Collector emitter saturation voltage
Cut-off frequency
Coupling capacitance
IF = 10 mA, IC = 0.5 mA
VCE = 5 V, IF = 10 mA, RL = 1 Ω
f = 1 MHz
VCEsat
fc
Ck
0.3
V
110
kHz
0.3
pF
Note
Tamb = 25 °C unless otherwise specified.
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
CURRENT TRANSFER RATIO
PARAMETER
TEST CONDITION
IC/IF
VCE = 20 V, IF = 10 mA
SYMBOL
CTR
MIN.
100
TYP.
MAX.
UNIT
%
MAXIMUM SAFETY RATINGS
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
INPUT
Forward current
IF
130
mA
OUTPUT
Power dissipation
Pdiss
265
mW
COUPLER
Rated impulse voltage
Safety temperature
VIOTM
Tsi
6
kV
150
°C
Note
According to DIN EN 60747-5-5 see figure 1. This optocoupler is suitable for safe electrical isolation only within the safety ratings. Compliance
with the safety ratings shall be ensured by means of suitable protective circuits.
www.vishay.com
784
For technical questions, contact: optocoupler.answers@vishay.com
Document Number: 83531
Rev. 1.8, 16-May-08
Share Link: 