AD607 查看數據表（PDF） - Analog Devices
零件编号
产品描述 (功能)
生产厂家
AD607 Datasheet PDF : 24 Pages
| |||
AD607–SPECIFICATIONS (@ TA = + 25°C, Supply = 3.0 V, IF = 10.7 MHz, unless otherwise noted)
Model
Conditions
AD607ARS
Min Typ
Max
DYNAMIC PERFORMANCE
MIXER
Maximum RF and LO Frequency Range For Conversion Gain > 20 dB
500
Maximum Mixer Input Voltage
For Linear Operation; Between RFHI and RFLO
± 54
Input 1 dB Compression Point
RF Input Terminated in 50 Ω
–15
Input Third-Order Intercept
RF Input Terminated in 50 Ω
–5
Noise Figure
Matched Input, Max Gain, f = 83 MHz, IF = 10.7 MHz
14
Matched Input, Max Gain, f = 144 MHz, IF = 10.7 MHz
12
Maximum Output Voltage at MXOP
ZIF = 165 Ω, at Input Compression
± 1.3
Mixer Output Bandwidth at MXOP
–3 dB, ZIF = 165 Ω
45
LO Drive Level
Mixer LO Input Terminated in 50 Ω
–16
LO Input Impedance
LOIP to VMID
1
Isolation, RF to IF
RF = 240 MHz, IF = 10.7 MHz, LO = 229.3 MHz
30
Isolation, LO to IF
RF = 240 MHz, IF = 10.7 MHz, LO = 229.3 MHz
20
Isolation, LO to RF
RF = 240 MHz, IF = 10.7 MHz, LO = 229.3 MHz
40
Isolation, IF to RF
RF = 240 MHz, IF = 10.7 MHz, LO = 229.3 MHz
70
IF AMPLIFIERS
Noise Figure
Input 1 dB Compression Point
Output Third-Order Intercept
Maximum IF Output Voltage at IFOP
Output Resistance at IFOP
Bandwidth
Max Gain, f = 10.7 MHz
IF = 10.7 MHz
IF = 10.7 MHz
ZIF = 600 Ω
From IFOP to VMID
–3 dB at IFOP, Max Gain
17
–15
+18
± 560
15
45
GAIN CONTROL
Gain Control Range
Gain Scaling
Gain Scaling Accuracy
Bias Current at GAIN/RSSI
Bias Current at GREF
Input Resistance at GAIN, GREF
(See Figures 43 and 44)
Mixer + IF Section, GREF to 1.5 V
GREF to 1.5 V
GREF to General Reference Voltage VR
GREF to 1.5 V, 80 dB Span
90
20
75/VR
±1
5
1
1
I AND Q DEMODULATORS
Required DC Bias at DMIP
Input Resistance at DMIP
Input Bias Current at DMIP
Maximum Input Voltage
Amplitude Balance
Quadrature Error
Phase Noise in Degrees
Demodulation Gain
Maximum Output Voltage
Output Offset Voltage
Output Bandwidth
From DMIP to VMID
IF > 3 MHz
IF ≤ 3 MHz
IF = 10.7 MHz, Outputs at 600 mV p-p, F = 100 kHz
IF = 10.7 MHz, Outputs at 600 mV p-p, F = 100 kHz
IF = 10.7 MHz, F = 10 kHz
Sine Wave Input, Baseband Output
RL ≥ 20 kΩ
Measured from IOUT, QOUT to VMID
Sine Wave Input, Baseband Output
VPOS/2
50
2
±150
±75
± 0.2
–1.2
–100
18
±1.23
10
1.5
PLL
Required DC Bias at FDIN
Input Resistance at FDIN
Input Bias Current at FDIN
Frequency Range
Required Input Drive Level
Acquisition Time to ± 3°
From FDIN to VMID
Sine Wave Input at Pin 1
IF = 10.7 MHz
VPOS/2
50
200
0.4 to 12
400
16.5
POWER-DOWN INTERFACE
Logical Threshold
Input Current for Logical High
Turn-On Response Time
Standby Current
POWER SUPPLY
Supply Range
Supply Current
OPERATING TEMPERATURE
TMIN to TMAX
For Power Up on Logical High
To PLL Locked
Midgain, IF = 10.7 MHz
Operation to 2.7 V Minimum Supply Voltage
Operation to 4.5 V Minimum Supply Voltage
2
75
16.5
550
2.7
5.5
8.5
–25
+85
–40
+85
Specifications subject to change without notice.
Units
MHz
mV
dBm
dBm
dB
dB
V
MHz
dBm
kΩ
dB
dB
dB
dB
dB
dBm
dBm
mV
Ω
MHz
dB
mV/dB
dB/V
dB
µA
µA
MΩ
V dc
kΩ
µA
mV
mV
dB
Degrees
dBc/Hz
dB
V
mV
MHz
V dc
kΩ
nA
MHz
mV
µs
V dc
µA
µs
µA
V
mA
°C
°C
–2–
REV. 0
Share Link: 