SN74LS163AMEL 查看數據表（PDF） - ON Semiconductor

零件编号

产品描述 (功能)

生产厂家

SN74LS163AMEL

BCD Decade Counters/4−Bit Binary Counters

ON Semiconductor 

SN74LS161A, SN74LS163A

STATE DIAGRAM

LS161A • LS163A

0

1

2

3

4

15

5

14

6

LOGIC EQUATIONS

Count Enable = CEP • CET • PE

TC for LS161A & LS163A = CET • Q0 • Q1 • Q2 • Q3

Preset = PE • CP + (rising clock edge)

Reset = MR (LS161A)

Reset = SR • CP + (rising clock edge)

Reset = (LS163A)

13

7

12

11

10

9

8

FUNCTIONAL DESCRIPTION

The LS161A/163A are 4-bit synchronous counters with

a synchronous Parallel Enable (Load) feature. The counters

consist of four edge-triggered D flip-flops with the

appropriate data routing networks feeding the D inputs. All

changes of the Q outputs (except due to the asynchronous

Master Reset in the LS161A) occur as a result of, and

synchronous with, the LOW to HIGH transition of the Clock

input (CP). As long as the set-up time requirements are met,

there are no special timing or activity constraints on any of

the mode control or data inputs.

Three control inputs — Parallel Enable (PE), Count

Enable Parallel (CEP) and Count Enable Trickle (CET) —

select the mode of operation as shown in the tables below.

The Count Mode is enabled when the CEP, CET, and PE

inputs are HIGH. When the PE is LOW, the counters will

synchronously load the data from the parallel inputs into the

flip-flops on the LOW to HIGH transition of the clock.

Either the CEP or CET can be used to inhibit the count

sequence. With the PE held HIGH, a LOW on either the CEP

or CET inputs at least one set-up time prior to the LOW to

HIGH clock transition will cause the existing output states

to be retained. The AND feature of the two Count Enable

inputs (CET•CEP) allows synchronous cascading without

external gating and without delay accumulation over any

practical number of bits or digits.

The Terminal Count (TC) output is HIGH when the Count

Enable Trickle (CET) input is HIGH while the counter is in

its maximum count state (HLLH for the BCD counters,

HHHH for the Binary counters). Note that TC is fully

decoded and will, therefore, be HIGH only for one count

state.

The LS161A and LS163A count modulo 16 following a

binary sequence. They generate a TC when the CET input is

HIGH while the counter is in state 15 (HHHH). From this

state they increment to state 0 (LLLL).

The Master Reset (MR) of the LS161A is asynchronous.

When the MR is LOW, it overrides all other input conditions

and sets the outputs LOW. The MR pin should never be left

open. If not used, the MR pin should be tied through a

resistor to VCC, or to a gate output which is permanently set

to a HIGH logic level.

The active LOW Synchronous Reset (SR) input of the

LS163A acts as an edge-triggered control input, overriding

CET, CEP and PE, and resetting the four counter flip-flops

on the LOW to HIGH transition of the clock. This simplifies

the design from race-free logic controlled reset circuits, e.g.,

to reset the counter synchronously after reaching a

predetermined value.

*SR PE CET

L

X

X

H

L

X

HH H

HH

L

HH X

*For the LS163A only.

MODE SELECT TABLE

CEP Action on the Rising Clock Edge ( )

X

RESET (Clear)

X

LOAD (Pn → Qn)

H

COUNT (Increment)

X

NO CHANGE (Hold)

L

NO CHANGE (Hold)

H = HIGH Voltage Level

L = LOW Voltage Level

X = Don’t Care

http://onsemi.com

3

Share Link: