HIP6301EVAL1 查看數據表（PDF） - Renesas Electronics

零件编号

产品描述 (功能)

生产厂家

HIP6301EVAL1

Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller

Renesas Electronics 

HIP6311

NOT RECOMMENDED FOR NEW DESIGNS

NO RECOMMENDED REPLACEMENT

contact our Technical Support Center at

1-888-INTERSIL or www.intersil.com/tsc

Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller

DATASHEET

FN4817

Rev 3.00

December 27, 2004

The HIP6311 multi-phase PWM control IC together with its

companion gate drivers, the HIP6601, HIP6602 or HIP6603

and internal MOSFETs provides a precision voltage

regulation system for advanced microprocessors.

Multiphase power conversion is a marked departure from

earlier single phase converter configurations previously

employed to satisfy the ever increasing current demands of

modern microprocessors. Multi-phase convertors, by

distributing the power and load current results in smaller and

lower cost transistors with fewer input and output capacitors.

These reductions accrue from the higher effective

conversion frequency with higher frequency ripple current

due to the phase interleaving process of this topology. For

example, a three phase convertor operating at 350kHz will

have a ripple frequency of 1.05MHz. Moreover, greater

convertor bandwidth of this design results in faster response

to load transients.

Outstanding features of this controller IC include

programmable VID codes from the microprocessor that

range from 1.100V to 1.850V with a system accuracy of

0.8%. Pull up currents on these VID pins eliminates the

need for external pull up resistors. In addition “droop”

compensation, used to reduce the overshoot or undershoot

of the CORE voltage, is easily programmed with a single

resistor.

Another feature of this controller IC is the PGOOD monitor

circuit which is held low until the CORE voltage increases,

during its Soft-Start sequence, to within 10% of the

programmed voltage. Over-voltage, 15% above

programmed CORE voltage, results in the converter shutting

down and turning the lower MOSFETs ON to clamp and

protect the microprocessor. Under voltage is also detected

and results in PGOOD low if the CORE voltage falls 10%

below the programmed level. Over-current protection

reduces the regulator current to less than 25% of the

programmed trip value. These features provide monitoring

and protection for the microprocessor and power system.

Features

• Multi-Phase Power Conversion

• Precision Channel Current Sharing

- Loss Less Current Sampling - Uses rDS(ON)

• Precision CORE Voltage Regulation

- 0.8% System Accuracy Over Temperature

• Microprocessor Voltage Identification Input

- 5-Bit VID Input

- 1.100V to 1.850V in 25mV Steps

- Programmable “Droop” Voltage

• Fast Transient Recovery Time

• Over Current Protection

• Automatic Selection of 2, 3, or 4 Phase Operation

• High Ripple Frequency, (Channel Frequency) Times

Number Channels . . . . . . . . . . . . . . . . . .100kHz to 6MHz

• Pb-Free Available (RoHS Compliant)

Ordering Information

PART NUMBER TEMP. (°C)

PACKAGE

PKG.

DWG. #

HIP6311CB

0 to 70 20 Ld SOIC

M20.3

HIP6311CBZ (Note)

0 to 70 20 Ld SOIC (Pb-free) M20.3

HIP6311CBZA (Note) 0 to 70 20 Ld SOIC (Pb-free) M20.3

HIP6301EVAL1

Evaluation Platform

*Add “-T” suffix to part number for tape and reel packaging.

NOTE: Intersil Pb-free products employ special Pb-free material

sets; molding compounds/die attach materials and 100% matte tin

plate termination finish, which are RoHS compliant and compatible

with both SnPb and Pb-free soldering operations. Intersil Pb-free

products are MSL classified at Pb-free peak reflow temperatures that

meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.

Pinout

HIP6311 (SOIC)

TOP VIEW

VID4 1

VID3 2

VID2 3

VID1 4

VID0 5

COMP 6

FB 7

FS/DIS 8

GND 9

VSEN 10

20 VCC

19 PGOOD

18 PWM4

17 ISEN4

16 ISEN1

15 PWM1

14 PWM2

13 ISEN2

12 ISEN3

11 PWM3

FN4817 Rev 3.00

December 27, 2004

Page 1 of 17

Share Link: