MAX9005ESA 查看數據表（PDF） - Maxim Integrated

零件编号

产品描述 (功能)

生产厂家

MAX9005ESA

Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs

Maxim Integrated 

Low-Power, High-Speed, Single-Supply

Op Amp + Comparator + Reference ICs

ELECTRICAL CHARACTERISTICS (continued)

(VDD = +2.5V to +5.5V, VSS = 0, SHDN = VDD (MAX9001/MAX9004 only), VCM(OP AMP) = 0, VAOUT = VDD / 2, VCM(COMP) = 0 (for

MAX9001/MAX9002/MAX9004/MAX9005), COUT = low, IOUT(REF) = 0, TA = TMIN to TMAX, unless otherwise noted. Typical values are

at VDD = 5V and TA = +25°C.)

PARAMETER

SYMBOL

CONDITIONS

Input Bias Current

Input Offset Current

IBIAS

IOS

MAX9001/MAX9002/MAX9004/MAX9005

Common-Mode

Voltage Range

VCM

Guaranteed by CMRR test

Common-Mode

Rejection Ratio

CMRR

MAX9001/MAX9002/MAX9004/MAX9005,

0.15V ≤ VCM ≤ (VDD - 1.1V), VDD = 5.5V

Power-Supply Rejection

Ratio

PSRR VDD = 2.5V to 5.5V

Output Voltage Swing

Output Short-Circuit

Current

VOL/VOH

(VCIN+ - VCIN-) VDD - VOH

≥ 20mV

VOL

ISOURCE = 10µA

ISOURCE = 4mA

ISINK = 10µA

ISINK = 4mA

Disabled Mode Output

Leakage

Propagation Delay

IOUT

(DISABLED)

tPD+, tPD-

VSHDN ≤ (0.3V x VDD), VCOUT = 0 to VDD

VOD = 25mV, RL = 10kΩ, CL = 15pF (Note 4)

Rise/Fall Time

tR, tF

VDD = 5V, RL = 10kΩ, CL = 15pF (Note 5)

Shutdown Delay Time

Enable Delay Time

Power-On Time

VOLTAGE REFERENCE (MAX9000/MAX9001/MAX9003/MAX9004)

Output Voltage

VREF

MAX900_ES_, VDD = 5V, TA = +25°C

Output Voltage

Temperature Coefficient

TCVREF

Line Regulation

VDD = 2.5V to 5.5V

Load Regulation

VDD = 5V,

IOUT = 0 to 1mA

Sourcing

Sinking

Output Short-Circuit

Current

Disabled Mode Output

Leakage

Shorted to VSS

Shorted to VDD

VSHDN ≤ (0.3V x VDD), VREF = 0 to VDD

Output Noise

0.1Hz to 10Hz

Shutdown Delay Time

Enable Delay Time

RL = 100kΩ to VSS, VREF within 1%

Power-On Time

RL = 100kΩ to VSS, VREF within 1%

Capacitive Load Stability

MIN TYP MAX UNITS

8

80

nA

±2

±15

nA

VSS -

0.15

VDD -

1.1

V

72

100

dB

72

100

dB

5

400

mV

5

400

55

mA

±0.01 ±1

µA

185

ns

10

ns

100

ns

100

ns

100

ns

1.218 1.230 1.242

V

8

ppm/°C

20

250 µV/V

0.15

0.8 mV/mA

0.6

2.0 mV/mA

6

mA

10

±0.01 ±1

µA

20

1

16

16

0 to 100

µVp-p

µs

µs

µs

nF

Note 1: Comparator Input Offset is defined as the center of the input-referred hysteresis zone.

Note 2: Measured at VCM(COMP) = 0 for the MAX9001/MAX9002/MAX9004/MAX9005; or VCM(COMP) = VREF for the MAX9000/MAX9003.

Note 3: Input-referred hysteresis is defined as the difference of the trip points required to change comparator output states.

Note 4: VOD is the overdrive that is beyond the offset and hysteresis-determined trip points.

Note 5: Rise and fall times are measured between 10% and 90% at COUT.

4 _______________________________________________________________________________________

Share Link: