TISP3072F3D 查看數據表（PDF） - Bourns, Inc
零件编号
产品描述 (功能)
生产厂家
TISP3072F3D Datasheet PDF : 12 Pages
| |||
TISP30xxF3 (LV) Overvoltage Protector Series
APPLICATIONS INFORMATION
Electrical Characteristics
The electrical characteristics of a TISP® device are strongly dependent on junction temperature, TJ. Hence, a characteristic value will depend
on the junction temperature at the instant of measurement. The values given in this data sheet were measured on commercial testers, which
generally minimize the temperature rise caused by testing. Application values may be calculated from the parameters’ temperature coefficient,
the power dissipated and the thermal response curve, Zθ (see M. J. Maytum, “Transient Suppressor Dynamic Parameters.” TI Technical
Journal, vol. 6, No. 4, pp.63-70, July-August 1989).
Lightning Surge
Wave Shape Notation
Most lightning tests, used for equipment verification, specify a unidirectional sawtooth waveform which has an exponential rise and an
exponential decay. Wave shapes are classified in terms of peak amplitude (voltage or current), rise time and a decay time to 50 % of the
maximum amplitude. The notation used for the wave shape is amplitude, rise time/decay time. A 50 A, 5/310 µs wave shape would have a
peak current value of 50 A, a rise time of 5 µs and a decay time of 310 µs. The TISP® device surge current graph comprehends the wave
shapes of commonly used surges.
Generators
There are three categories of surge generator type, single wave shape, combination wave shape and circuit defined. Single wave shape
generators have essentially the same wave shape for the open circuit voltage and short circuit current (e.g., 10/1000 µs open circuit voltage
and short circuit current). Combination generators have two wave shapes, one for the open circuit voltage and the other for the short circuit
current (e.g., 1.2/50 µs open circuit voltage and 8/20 µs short circuit current). Circuit specified generators usually equate to a combination
generator, although typically only the open circuit voltage waveshape is referenced (e.g. a 10/700 µs open circuit voltage generator typically
produces a 5/310 µs short circuit current). If the combination or circuit defined generators operate into a finite resistance, the wave shape
produced is intermediate between the open circuit and short circuit values.
Current Rating
When the TISP® deviceswitches into the on-state, it has a very low impedance. As a result, although the surge wave shape may be defined in
terms of open circuit voltage, it is the current wave shape that must be used to assess the required TISP® surge capability. As an example, the
ITU-T K.21 1.5 kV, 10/700 µs open circuit voltage surge is changed to a 38 A, 5/310 µs current waveshape when driving into a short circuit.
Thus, the TISP® surge current capability, when directly connected to the generator, will be found for the ITU-T K.21 waveform at 310 µs on the
surge graph and not 700 µs. Some common short circuit equivalents are tabulated below:
Standard
ITU-T K.21
ITU-T K.20
IEC 61000-4-5, combination wave generator
Telcordia GR-1089-CORE
Telcordia GR-1089-CORE
FCC Part 68, Type A
FCC Part 68,Type A
FCC Part 68, Type B
Open Circuit Voltage
1.5 kV, 10/700 µs
1 kV, 10/700 µs
1.0 kV, 1.2/50 µs
1.0 kV, 10/1000 µs
2.5 kV, 2/10 µs
1.5 kV, <10/>160 µs
800 V, <10/>560 µs
1.5 kV, 9/720 µs
Short Circuit Current
37.5 A, 5/310 µs
25 A, 5/310 µs
500 A, 8/20 µs
100 A, 10/1000 µs
500 A, 2/10 µs
200 A,<10/>160 µs
100 A,<10/>160 µs
37.5 A, 5/320 µs
Any series resistance in the protected equipment will reduce the peak circuit current to less than the generators’ short circuit value. A 1 kV
open circuit voltage, 100 A short circuit current generator has an effective output impedance of 10 Ω (1000/100). If the equipment has a series
resistance of 25 Ω, then the surge current requirement of the TISP® device becomes 29 A (1000/35) and not 100 A.
MARCH 1994 - REVISED MARCH 2006
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
Share Link: 