OP290 查看數據表（PDF） - TT Electronics.
零件编号
产品描述 (功能)
生产厂家
OP290 Datasheet PDF : 9 Pages
| |||
OP290 Series
Electrical Specifications
Electrical Characteristics (TA = 25° C unless otherwise noted)
SYMBOL
PARAMETER
MIN TYP MAX UNITS
TEST CONDITIONS
Input Diode
Apertured Radiant Incidence
OP290A
OP290B
OP290C
210 -
-
180 - 300
150 -
-
IF = 1.50 A(1)(2)
Measured into a 0.250” [6.35mm] aperture
0.2” (5.08 mm) from the tip of the lens.
OP291A
OP291C
16
-
-
10
-
-
IF = 100 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
0.2” (5.08 mm) from the tip of the lens.
OP292A
2.7
-
-
IF = 20 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
0.2” (5.08 mm) from the tip of the lens.
EE
(2)
(APT)
OP293A
OP293B
OP293C
OP294
OP295A
OP295B
16
-
-
13 22 26
10
-
-
IF = 100 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
0.2” (5.08 mm) from the tip of the lens.
0.50 - 1.50
IF = 5 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
0.200” (5.08mm) from the tip of the lens.
44
33
-
-
-
77
mW/cm2
IF = 1.50 A(1)(2)
Measured into a 0.250” [6.35mm] aperture
1.129” (28.7 mm) from the tip of the lens.
OP296A
OP296B
3.6
-
-
2.6
-
6.6
IF = 100 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
1.129” (28.7 mm) from the tip of the lens.
OP297FAB
OP297A
OP297B
2.4
-
-
0.7
-
-
0.5 1.0 1.3
IF = 20 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
1.129” (28.7 mm) from the tip of the lens.
OP298A
OP298B
OP298C
3.0
-
-
2.4
-
4.8
1.8
-
-
IF = 100 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
0.2” (5.08 mm) from the tip of the lens.
OP298AA
OP298AD
3.5
-
-
8.5
-
-
IF = 100 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
1.129” (28.7 mm) from the tip of the lens.
OP299
0.15 - 0.45
IF = 100 mA(1)(2)
Measured into a 0.250” [6.35mm] aperture
1.129” (28.7 mm) from the tip of the lens.
Notes:
1. Measurement is taken at the end of a single 100 µs pulse. Heating due to increased pulse rate or pulse width will cause a decrease in reading.
2. Measurement of the average apertured radiant energy incident upon a sensing area 0.250” (6.35 mm) in diameter perpendicular to and centered
on the mechanical axis of the lens and the specified distance from the end of the device. On all models in this series, EE(APT) is not necessarily
uniform within the measured area.
3. Measurement is taken at the end of a single 10 ms pulse. Heating due to increased pulse rate or pulse width will cause a decrease in reading.
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
OPTEK Technology, Inc.
1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200
www.optekinc.com | www.ttelectronics.com
Issue D 07/2016 Page 5
Share Link: 