CY7C1440AV33-167BZXC 查看數據表（PDF） - Cypress Semiconductor
零件编号
产品描述 (功能)
生产厂家
CY7C1440AV33-167BZXC Datasheet PDF : 31 Pages
| |||
CY7C1440AV33
CY7C1442AV33
CY7C1446AV33
Pin Definitions (continued)
Name
CE2
CE3
OE
ADV
ADSP
ADSC
ZZ
DQs, DQPX
VDD
VSS
VSSQ
VDDQ
MODE
TDO
TDI
TMS
TCK
NC
NC/72M,
NC/144M,
NC/288M,
NC/576M,
NC/1G
I/O
Description
Input-
Synchronous
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE3 to select/deselect the device. CE2 is sampled only when a new external
address is loaded.
Input-
Synchronous
Input-
Asynchronous
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE1 and CE2 to select/deselect the device. Not available for AJ package version. Not
connected for BGA. Where referenced, CE3 is assumed active throughout this document
for BGA. CE3 is sampled only when a new external address is loaded.
Output Enable, asynchronous input, active LOW. Controls the direction of the I/O pins.
When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are tri-stated,
and act as input data pins. OE is masked during the first clock of a read cycle when emerging
from a deselected state.
Input-
Advance Input signal, sampled on the rising edge of CLK, active LOW. When asserted,
Synchronous it automatically increments the address in a burst cycle.
Input-
Synchronous
Input-
Synchronous
Address Strobe from Processor, sampled on the rising edge of CLK, active LOW.
When asserted LOW, addresses presented to the device are captured in the address
registers. A1: A0 are also loaded into the burst counter. When ADSP and ADSC are both
asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted HIGH.
Address Strobe from Controller, sampled on the rising edge of CLK, active LOW.
When asserted LOW, addresses presented to the device are captured in the address
registers. A1: A0 are also loaded into the burst counter. When ADSP and ADSC are both
asserted, only ADSP is recognized.
Input-
ZZ “sleep” Input, active HIGH. When asserted HIGH places the device in a
Asynchronous non-time-critical “sleep” condition with data integrity preserved. For normal operation, this
pin has to be LOW or left floating. ZZ pin has an internal pull-down.
I/O-
Synchronous
Power Supply
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is
triggered by the rising edge of CLK. As outputs, they deliver the data contained in the
memory location specified by the addresses presented during the previous clock rise of the
read cycle. The direction of the pins is controlled by OE. When OE is asserted LOW, the
pins behave as outputs. When HIGH, DQs and DQPX are placed in a tri-state condition.
Power supply inputs to the core of the device.
Ground
Ground for the core of the device.
I/O Ground Ground for the I/O circuitry.
I/O Power Supply Power supply for the I/O circuitry.
Input-
Static
Selects Burst Order. When tied to GND selects linear burst sequence. When tied to VDD
or left floating selects interleaved burst sequence. This is a strap pin and should remain
static during device operation. Mode Pin has an internal pull-up.
JTAG serial
output
Synchronous
Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the
JTAG feature is not being utilized, this pin should be disconnected. This pin is not available
on TQFP packages.
JTAG serial input Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature
Synchronous is not being utilized, this pin can be disconnected or connected to VDD. This pin is not
available on TQFP packages.
JTAG serial input Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG feature
Synchronous is not being utilized, this pin can be disconnected or connected to VDD. This pin is not
available on TQFP packages.
JTAG-
Clock
–
Clock input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin must
be connected to VSS. This pin is not available on TQFP packages.
No Connects. Not internally connected to the die
–
No Connects. Not internally connected to the die. NC/72M, NC/144M, NC/288M, NC/576M
and NC/1G are address expansion pins are not internally connected to the die.
Document #: 38-05383 Rev. *E
Page 7 of 31
[+] Feedback
Share Link: 