LT1684 查看數據表（PDF） - Linear Technology

零件编号

产品描述 (功能)

生产厂家

LT1684

Micropower Ring Tone Generator

Linear Technology 

LT1684

PI FU CTIO S

IN B (Pin 1): PWM Negative Input. Input is isolated from

digital source by ~100pF series capacitor. A 10k resistor

can be connected to the IN B pin in series with the isolation

capacitor for transient protection. The PWM receiver imple-

ments a diode forward drop of input hysteresis (relative to

IN A). This hysteresis and internal signal limiting assure

common mode glitch rejection with isolation capacitor

mismatches up to 2:1. For maximum performance, how-

ever, effort should be made to match the two PWM input

isolation capacitors. Pin IN B is differentially clamped to

pin IN A through back-to-back diodes. This results in a

high impedance differential input through ±100mV be-

yond the input thresholds. 5k internal input resistors yield

a 10k (nominal) differential overdrive impedance.

COMP1 (Pin 2): Output Amplifier Primary Compensation.

Connect a 100pF capacitor from pin COMP1 to pin OUT.

COMP2 (Pin 3): Output Amplifier Secondary Compensa-

tion. Connect a 20pF capacitor from pin COMP2 to pin

OUT.

LIM – (Pin 4): Output Amplifier Current Sink Limit. Pin

implements IOUT • R = VBE current clamp. Internal clamp

resistor has a typical value of 3.5Ω. For maximum current

drive capability (190mA typical) short pin to pin V –.

Reduction of current sink capability is achieved by placing

additional resistance from pin LIM – to pin V –. (i.e. An

external 3.5Ω resistance from pin LIM – to pin V – will

reduce the current sinking capability of the output ampli-

fier by approximately 50%.)

V – (Pin 5): Local Negative Supply. Typically connected to

the source of the active tracking supply P-channel MOSFET.

V – rail voltage is GATE – self-bias voltage less the MOSFET

VGS. Typical P-channel MOSFET characteristics provide

ATREF – V – ≈ 10V.

GATE– (Pin 6): Negative Power Supply FET Gate Drive. Pin

sources current from pull-down resistor to bias gate of

active tracking supply P-channel MOSFET. Self-biases to

a typical value of –14V, referenced to pin ATREF. Pull-down

resistor value is determined such that current sourced

from the GATE – pin remains greater than 50µA at mini-

mum output signal voltage and less than 10mA at maxi-

mum output signal voltage.

ATREF (Pin 7): Active Tracking Supply Reference. Typi-

cally connected to pin OUT. Pin bias current is the differ-

ence between the magnitudes of GATE + pin bias and

GATE– pin bias (IATREF = IGATE+ – IGATE–).

OUT (Pin 8): Ring Tone Output Pin. Output of active filter

amplifier/buffer. Used as reference voltage for internal

functions of IC. Usually shorted to pin ATREF to generate

reference for active tracking supply circuitry. Connect a 1A

(1N4001-type) diode between V + and OUT and a

1A Schottky diode from V – to OUT for line transient

protection.

LIM+ (Pin 9): Output Amplifier Current Source Limit. Pin

implements IOUT • R = VBE current clamp. Internal clamp

resistor has a typical value of 3.5Ω. For maximum current

drive capability (190mA typical) short pin LIM + to pin

OUT. Reduction of current source capability is achieved by

placing additional resistance from pin LIM + to pin OUT.

(i.e. An external 3.5Ω resistance from pin LIM + to pin OUT

will reduce the current sourcing capability of the output

amplifier by approximately 50%.)

V + (Pin 10): Local Positive Supply. Typically connected to

the source of the active tracking supply N-channel MOSFET.

This condition should be made using a ferrite bead.

Operating V + rail voltage is GATE + self-bias voltage less

the MOSFET VGS. Typical N-channel MOSFET characteris-

tics provide V + – ATREF ≈ 10V.

GATE + (Pin 11): Positive Power Supply FET Gate Drive.

Pin sinks current from pull-up resistor to bias gate of

active tracking supply N-channel MOSFET. Self-biases to

a typical value of 14V, referenced to pin ATREF. Pull-up

resistor value is determined such that sink current into

GATE + pin remains greater than 50µA at maximum output

signal voltage and less than 10mA at minimum output

signal voltage.

AMPIN (Pin 12): Output Amplifier Input. Connected to

external filter components through series protection re-

sistor (usually 5k). Thevenin DC resistance of external

filter and protection components should be 10k for opti-

mum amplifier offset performance. See Applications In-

formation section.

5

Share Link: