AD8018(Rev0) 查看數據表（PDF） - Analog Devices
零件编号
产品描述 (功能)
生产厂家
AD8018 Datasheet PDF : 19 Pages
| |||
AD8018
Table I. Resistor Selection Guide
Gain
–1
+1
+2
+3
+4
+5
RF (⍀)
681
1k
750
511
340
230
RG (⍀)
681
∞
750
256
113
59
POWER-DOWN FEATURES
Two digitally programmable logic pins, PWDN1 and PWDN0,
are available on the TSSOP-14 package to select among three
different modes of operation, full power, standby and shutdown.
The DGND pin is the logic ground reference. The logic thresh-
old voltage is established 1 V above DGND. In a typical 5 V
single-supply application, the DGND pin is connected to analog
ground. If PWDN1, PWDN0, and DGND are left unconnected,
the AD8018 will operate at full power.
Table II. Power-Down Features and Truth Table
PWDN0 PWDN1 State
Supply Output
Current Impedance
High
Low
High
Low
High
High
Low
Low
Full Power
Standby
Standby
Disabled
18 mA
9 mA
9 mA
300 µA
Low
Low
Low
High
POWER SUPPLY AND DECOUPLING
The AD8018 can be powered with a good quality (i.e., low-noise)
supply anywhere in the range from 3.3 V to 8 V. However, in
order to optimize the ADSL upstream drive capability to +13 dBm
and maintain the best Spurious Free Dynamic Range (SFDR),
the AD8018 circuit should be supplied with a well regulated 5 V
supply. The 5 V supplied at the USB port may be poorly regu-
lated. Improving the quality of the 5 V supply will optimize the
performance of the AD8018 in a USB-supplied CPE ADSL
modem. This can be accomplished through the use of a step-up
dc-to-dc converter or switching power supply followed by a low
dropout (LDO) regulator such as the ADP3331 (see Figure 6).
Setting R1 to be 953 kΩ and R2 to be 301 kΩ will result in a
VOUT of 5 V.
Careful attention must be paid to decoupling the power supply
pins at the output of the dc-to-dc converter, the output of the
LDO regulator and the supply pins of the AD8018. High-quality
capacitors with low equivalent series resistance (ESR) such as
multilayer ceramic capacitors (MLCCs) should be used to mini-
mize supply voltage ripple and power dissipation. A large, usually
tantalum, 10 µF to 47 µF capacitor located in proximity to the
AD8018 is required to provide good decoupling for lower fre-
quency signals. In addition, 0.1 µF MLCC decoupling capacitors
should be located as close to each of the power supply pins as is
physically possible, no more than 1/8 inch away. An additional
large (4.7 µF to 10 µF) tantalum capacitor should be placed on the
board near the supply terminals to supply current for fast, large-
signal changes at the AD8018 outputs.
VIN
C1
0.47F
ERR
ADP3331
OUT
IN
FB
SD
GND
ON
OFF
R3
330k⍀
R1
953k⍀
R2
301k⍀
EOUT
VOUT
C2
0.47F
Figure 6. ADP3331 LDO
METHOD FOR GENERATING A MIDSUPPLY VOLTAGE
To operate an amplifier on a single voltage supply, a voltage
midway between the supply and ground must be generated to
properly bias the inputs and the outputs.
A voltage divider can be created with two equal value resistors
(Figure 7). There is a trade-off between the power consumed by
the divider and the voltage drop across these resistors due to the
positive input bias currents. Selecting 2.5 kΩ for R1 and R2 will
create a voltage divider that draws only 1 mA from a 5 V supply.
The voltage generated with this topology can vary due to the
temperature coefficient (TC) of resistance. Resistors that are
closely matched and have a low TC will minimize variations in
the voltage reference due to temperature. One should also be
sure to use a decoupling capacitor (0.1 µF) at the node where
VREF is generated.
5V
R1
2.5k⍀
R2
2.5k⍀
VREF
0.1F
Figure 7. Midsupply Reference
DIFFERENTIAL TESTING
The test circuit shown in TPC 13 is used for measuring the dif-
ferential distortion of the AD8018. A single-ended test signal is
applied to the inverting input of the AD8138 differential driver
with the noninverting input grounded. Applying the differential
output of the AD8138 through 100 Ω resistors serves to isolate
the inputs of the AD8018 differential driver and provide a well-
balanced low-distortion input signal. The differential load (RL)
of the AD8018 can be set to the equivalent of the line imped-
ance reflected through a transformer. The AD9632 converts
the differential output voltage back to a single-ended signal.
The differential-to- single-ended converter using the AD9632
has an attenuation of –26 dB and is wired with precision resis-
tors to optimize the balance of differential input signal. The
resulting smaller output signal can be easily measured using a
50 Ω spectrum analyzer.
REV. 0
–9–
Share Link: 