AD74111 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

AD74111

Low Cost, Low Power Mono Audio Codec

Analog Devices 

DFS

DCLK

DIN

DOUT

tFS

tFH

tFD

tCH

tCL

MSB

MSB

MSB–1

MSB–1

MSB–2

tDS

tDH

MSB–2

tDD

Figure 11. Serial Port (SPORT) Timing

AD74111

Serial Port Operating Modes

The serial port of the AD74111 can be programmed to operate

in a variety of modes depending on the requirements and flex-

ibility of the DSP to which it is connected. The two principal

modes of operation are Mixed mode and Data mode.

Mixed Mode

Mixed mode allows the control registers of the AD74111 to be

programmed and read back. It also allows data to be sent to the

DACs and data to be read from the ADCs. In Mixed mode,

there are separate data slots, each with its own frame synchroni-

zation signal (DFS) for control and DAC or ADC information.

The AD74111 powers up in Mixed mode by default to allow

the control registers to be programmed. Figure 13 shows the

default setting for Mixed mode.

Data Mode

Data mode can be used when programming or reading the

control registers is no longer required. Data mode provides a

frame synchronization (DFS) pulse for each sample of data.

Once the part has been programmed into Data mode, the only

way to change the control registers is to perform a hardware reset

to put the AD74111 back into Mixed mode. Figure 15 shows

the default setting for Data mode.

Data-Word Length

The AD74111 can be programmed to send DAC audio data

and receive ADC audio data in different word length formats of

16, 20, or 24 bits. The default mode is 16 bits, but this can be

changed by programming Control Register C for the appropriate

word length.

Selecting Master or Slave Mode

The initial operating mode of the AD74111 is determined by

the state of the DIN pin following a reset. If the DIN pin is high

during this time, Slave mode is selected. In Slave mode, the

DFS and DCLK pins are inputs and the control signals for

these pins must be provided by the DSP or other controller. If

the DIN pin is low immediately following a reset, the AD74111

will operate in Master mode.

Master Mode Operation

In Master mode, the DFS and DCLK pins are outputs from the

AD74111. This is the easiest mode in which to use the AD74111

because the correct timing relationship between sample rate,

DCLK, and DFS is controlled by the AD74111.

Slave Mode Operation

In Slave mode, the DFS and DCLK pins are inputs to the

AD74111. Care needs to be exercised when designing a system

to operate the AD74111 in this mode as the relationship between

the sample rate, DCLK, and DFS needs to be controlled by the

DSP or other controller and must be compatible with the inter-

nal DAC/ADC engine of the AD74111. Figure 12 shows a block

diagram of the DAC engine and the AD74111’s serial port. The

sample rate for the DAC engine is determined by the MCLK

and MCLK prescalers. The DAC engine will read data from the

DAC Data register at this rate. It is therefore important that the

serial port is updated at the same rate, as any error between the

two will accumulate and eventually cause the DAC engine to have

to resynchronize with the serial port, which will cause erroneous

values on the DAC output pins.

RESYNC*

LOAD DAT

DAC ENGINE

VOUT

DAC DATA REGISTER

DFS

DIN

SERIAL PORT

*RESYNC IS ONLY USED WHEN THE DAC BECOMES

UNSYNCHRONIZED WITH THE SERIAL PORT

Figure 12. DAC Engine

In most cases, it is easy to keep a DSP in synchronization with

the AD74111 if they are both run from the same clock or the

DSP clock is a multiple of the AD74111’s MCLK. In this case,

REV. 0

–11–

Share Link: