ADM1028ARQ 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

ADM1028ARQ

Remote Thermal Diode Monitor with Linear Fan Control

Analog Devices 

ADM1028

PIN CONFIGURATION

FAN_OFF 1

16 SDA

GPI 2

15 SCL

AUXRST 3

14 INT

GND 4 ADM1028 13 R_OFF

TOP VIEW

VCC3AUX 5 (Not to Scale) 12 THERMB

RST 6

11 THERMA/NTEST_OUT

R_RST 7

10 D+

FAN_SPD/NTEST_IN 8

9 D–

Pin No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

Mnemonic

FAN_OFF

GPI

AUXRST

GND

VCC3AUX

RST

R_RST

FAN_SPD/NTEST_IN

D–

D+

THERMA/NTEST_OUT

THERMB

R_OFF

INT

SCL

SDA

PIN FUNCTION DESCRIPTIONS

Description

Digital Output (Open Drain) Fan Off Request. When asserted low, this indicates a

request to shut off the fan independent of the FAN_SPD output. When negated (output

FET off) it indicates that the fan may be turned on.

Digital Input (12 V tolerant). This pin is a general-purpose logic input with 12 V toler-

ance. It can be programmed as an active high or active low input that sets Bit 4 of the

Interrupt Status Register. A voltage >2.2 V on this pin, represents a Logic “1,” while a

floating condition is interpreted as Logic “0.”

Digital Input. This pin can be driven low as an input to reset the ADM1028.

Ground. Power and signal ground.

Power 3.3 V Aux. Power source and voltage monitor input for power-on reset.

Digital Input. This pin can be pulled low externally to indicate to the ADM1028 that the

main system power has been removed. The ADM1028 will shut off the FAN_SPD out-

put and reset its R_OFF output.

Digital Output (Open Drain). This pin is a remote reset output that pulses low on

receipt of a specific SMBus message.

Analog Output/Test Input. An active-high input that enables NAND board-level

connectivity testing. Refer to section on NAND testing.

Used as an analog output for fan speed control when NAND test is not selected.

Remote Thermal Diode Negative Input. This is the negative input (current sink) from

the remote thermal diode. This also serves as the negative input into the A/D.

Remote Thermal Diode Positive Input. This is the positive input (current source) from

the remote thermal diode. This serves as the positive input into the A/D.

Digital Output (Open Drain with Integrated VCC3AUX Pull-Up). An active low thermal

overload output that indicates a violation of a temperature setpoint (over temperature).

The fan is on full-speed whenever this pin is asserted low. Acts as the output of the NAND

Tree when the ADM1028 is in NAND Tree Test Mode.

Digital Output (Open Drain). This pin is a second THERM signal. It can be used to

drive external circuitry with a different external pull-up supply rail.

Digital Output or Open Drain with Integrated VCC3AUX Pull-Up. Remote off (power-

down) output. This pin is driven high on receipt of a specific SMBus message. The pin

(and its associated register bit) remain high until the RST input is asserted low.

Digital Output (Open Drain), System Interrupt Output. This signal indicates a violation

of a set trip point. The output is enabled when Bit 1 of the Configuration Register is set

to 1. The default state is disabled.

Digital Input. SMBus Clock.

Digital I/O (Open Drain). SMBus Bidirectional Data.

–4–

REV. A

Share Link: