HT48CA5 查看數據表（PDF） - Holtek Semiconductor

零件编号

产品描述 (功能)

生产厂家

HT48CA5

Remote Type 8-Bit MCU

Holtek Semiconductor 

HT48RA5/HT48CA5

Timer/Event Counter 1 preload register. The

Timer/Event Counter 1 will still operate until the overflow

occurs (a Timer/Event Counter 1 reloading will occur at

the same time).

When the Timer/Event Counter 1 (reading TMR1H) is

read, the clock will be blocked to avoid errors. As this

may results in a counting error, this must be taken into

consideration by the programmer.

The definitions of the TMR1C are as shown.

Bit

No.

Label

Function

0~2 ¾ Unused bit, read as ²0²

To define the active edge of TMR1 pin

3 T1E input signal

(0/1: active on low to high/high to low)

4

T1ON

To enable/disable timer 1 counting

(0/1: disabled/enabled)

5

¾ Unused bit, read as ²0²

To define the operating mode

(T1M1, T1M0)

6 T1M0 01=Event count mode (external clock)

7 T1M1 10=Timer mode (internal clock)

11=Pulse width measurement mode

00=Unused

TMR1C (11H) Register

Input/Output Ports

There are 23 bi-directional input/output lines in the mi-

cro-controller, labeled from PA to PC and PF, which are

mapped to the data memory of [12H], [14H], [16H] and

[1CH], respectively. All of these I/O ports can be used as

input and output operations. For input operation, these

ports are non-latching, that is, the inputs must be ready

at the T2 rising edge of instruction ²MOV A,[m]² (m =

12H, 14H, 16H or 1CH). For output operation, all the

data is latched and remains unchanged until the output

latch is rewritten.

Each I/O line has its own control register (PAC, PBC,

PCC, PFC) to control the input/output configuration.

With this control register, CMOS output or Schmitt trig-

ger input with or without (depends on options) pull-high

resistor structures can be reconfigured dynamically (i.e.,

on-the fly) under software control. To function as an in-

put, the corresponding latch of the control register has to

be set as ²1². The pull-high resistor (if the pull-high re-

sistor is enabled) will be exhibited automatically. The in-

put sources also depends on the control register. If the

control register bit is ²1², the input will read the pad state

(²mov² and read-modify-write instructions”). If the con-

trol register bit is 0, the contents of the latches will move

to internal data bus (²mov² and read-modify-write in-

structions). The input paths (pad state or latches) of

read-modify-write instructions are dependent on the

control register bits. For output function, CMOS is the

only configuration. These control registers are mapped

to locations 13H, 15H, 17H and 1DH.

C o n tr o l B it

PU

D a ta B u s

DQ

W r ite C o n tr o l R e g is te r

C h ip R e s e t

CK Q

S

R e a d C o n tr o l R e g is te r

D a ta B it

D

Q

W r ite D a ta R e g is te r

( P B 0 o n ly )

PB0

EXT

R e a d D a ta R e g is te r

CK Q

S

M

U

X

M

U

X

PFD EN

( P B 0 o n ly )

S y s te m W a k e - u p ( P A o n ly )

P A W a k e - u p O p tio n

IN T fo r P F 0 O n ly

P F D fo r P B 0 O n ly , C o n tr o l= P B 0 D a ta R e g is te r

V DD

P A 0~P A 7

P B 0 /P F D

P B 1~P B 7

P C 0~P C 5

PF0

Input/Output Ports

Rev. 1.40

16

May 22, 2009

Share Link: