MAX17006BETP 查看數據表（PDF） - Maxim Integrated

零件编号

产品描述 (功能)

生产厂家

MAX17006BETP

1.2MHz, Low-Cost, High-Performance Chargers

Maxim Integrated 

1.2MHz, Low-Cost,

High-Performance Chargers

Setting Charge Voltage

The VCTL input adjusts the battery-output voltage,

VBATT, and determines the number of cells. For 3- and

4-cell applications, use the MAX17005B; for 2- and

3-cell applications, use the MAX17006B. Use the

MAX17015B to adjust the cell number and set the cell

voltage with a resistive voltage-divider from the output.

Based on the version of the part, the number of cells

and the level of VCTL should be set as in Table 1.

Table 1. Cell Configuration

VERSION NO. OF CELLS

LEVEL

MAX17005B

3

2.4V < VCTL < 4.2V

MAX17005B

4

0 < VCTL < 1.8V

MAX17006B

2

0 < VCTL < 1.8V

MAX17006B

MAX17015B

3

Sets FB

2.4V < VCTL < 4.2V

VCTL = AGND or VCTL = VAA

The MAX17005B/MAX17006B support from 4.2V/cell to

4.4V/cell, whereas the MAX17015B supports minimum

2.1V. The maximum voltage is determined with the

dropout performance of IC. When the required voltage

falls outside the range available with the MAX17005B or

MAX17006B, the MAX17015B should be used.

The charge-voltage regulation for the MAX17005B and

MAX17006B is calculated with the following equations:

VCELL

=

VAA

+

VAA

- VVCTL

6

for 3-cell selection of MAX17005B and MAX17006B,

4.2V > VCTL > 2.4V:

VCELL

=

VAA

+

VVCTL

6

for 2- or 4-cell selection of MAX17006B or MAX17005B,

respectively, 0 < VCTL < 1.8V. Connect VCTL to AGND

or to VAA for default 4.2V/cell battery-voltage setting.

For the MAX17015B, connect VCTL to AGND to set the

FB regulation point to 2.1V. The charge-voltage regula-

tion is calculated with the following equation:

VCHG _ REG

=

VFB _

SETPOINT

×

R8 + R7

R8

There are two constraints in choosing R7 and R8. The

resistors cannot be too small since they discharge the

battery, and they cannot be too large because FB pin

consumes less than 1μA of input bias current. Pick R8

to be approximately 10kΩ and then calculate R7.

FB regulation error (±0.5% max) and the tolerance of R7

and R8 both contribute to the error on the battery volt-

age. Use 0.1% feedback resistors for best accuracy.

Figure 3 shows the MAX17015B charge-voltage regula-

tion feedback network.

Setting Charge Current

The voltage at ISET determines the voltage across cur-

rent-sense resistor RS2. ISET can accept either analog

or digital inputs. The full-scale differential voltage

between CSIP and CSIN is 80mV (8A for RS2 = 10mΩ)

for the analog input, and 60mV (6A for RS2 = 10mΩ) for

the digital PWM input.

When the MAX17005B/MAX17006B/MAX17015B power

up and the charger is ready, if there is no clock edge

within 20ms, the circuit assumes ISET is an analog

input, and disables the PWM filter block. To configure

the charge current, force the voltage on ISET according

to the following equation:

ICHG

=

240mV

RS2

×

VISET

VAA

The input range for ISET is from 0 to VAA/2. To shut

down the charger, pull ISET below 26mV.

If there is a clock edge on ISET within 20ms, the PWM

filter is enabled and ISET accepts digital PWM input.

The PWM filter has a DAC with 8-bit resolution that cor-

responds to equivalent VCSIP-CSIN steps.

CSIN

MAX17015B

FB

COUT

R7

BATTERY

R8

Figure 3. MAX17015B Charge-Voltage Regulation Feedback

Network

12 ______________________________________________________________________________________

Share Link: