AD7273 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

AD7273

3MSPS,10-/12-Bit ADCs in 8-Lead TSOT

Analog Devices 

PRELIMINARY TECHNICAL DATA

AD7273/AD7274

Preliminary Technical Data

Power-up Time

The power-up time of the AD7273/AD7274 is TBD ns,

which means that with any frequency of SCLK up to 52

MHz, one dummy cycle will always be sufficient to allow

the device to power up. Once the dummy cycle is com-

plete, the ADC will be fully powered up and the input

signal will be acquired properly. The quite time tQUIET

must still be allowed from the point where the bus goes

back into three-state after the dummy conversion, to the

next falling edge of CS. When running at 3 MSPS

throughput rate, the AD7273/AD7274 will power up and

acquire a signal within ±0.5 LSB in one dummy cycle,

i.e. TBD ns.

When powering up from the Power-Down mode with a

dummy cycle, as in Figure 14, the track and hold which

was in hold mode while the part was powered down,

returns to track mode after the first SCLK edge the part

receives after the falling edge of CS. This is shown as

point A in Figure 14. Although at any SCLK frequency

one dummy cycle is sufficient to power the device up and

acquire VIN, it does not necessarily mean that a full

dummy cycle of 16 SCLKs must always elapse to power

up the device and acquire VIN fully; TBD ns will be suffi-

cient to power the device up and acquire the input signal.

If, for example, a 25 MHz SCLK frequency was applied

to the ADC, the cycle time would be 640 ns. In one

dummy cycle, 640 ns, the part would be powered up and

VIN acquired fully. However after TBD ns with a 25 MHz

SCLK only TBD SCLK cycles would have elapsed. At

this stage, the ADC would be fully powered up and the

signal acquired. So, in this case the CS can be brought

high after the 10th SCLK falling edge and brought low

again after a time tQUIET to initiate the conversion.

When power supplies are first applied to the AD7273/

AD7274, the ADC may either power up in the Power-

Down mode or in Normal mode. Because of this, it is best

to allow a dummy cycle to elapse to ensure the part is fully

powered up before attempting a valid conversion. Like-

wise, if it is intended to keep the part in the Power-Down

mode while not in use and the user wishes the part to

power up in Power-Down mode, then the dummy cycle

may be used to ensure the device is in Power-Down by

executing a cycle such as that shown in Figure 13. Once

supplies are applied to the AD7273/AD7274, the power

up time is the same as that when powering up from the

Power-Down mode. It takes approximately TBD ns to

power up fully if the part powers up in Normal mode. It is

not necessary to wait TBD ns before executing a dummy

cycle to ensure the desired mode of operation. Instead, the

dummy cycle can occur directly after power is supplied to

the ADC. If the first valid conversion is then performed

directly after the dummy conversion, care must be taken to

ensure that adequate acquisition time has been allowed. As

mentioned earlier, when powering up from the Power-

Down mode, the part will return to track upon the first

SCLK edge applied after the falling edge of CS.

However, when the ADC powers up initially after supplies

are applied, the track and hold will already be in track.

This means, assuming one has the facility to monitor the

ADC supply current, if the ADC powers up in the desired

mode of operation and thus a dummy cycle is not required

to change mode, then neither is a dummy cycle required

to place the track and hold into track.

POWER VERSUS THROUGHPUT RATE

By using the Power-Down mode on the AD7273/AD7274

when not converting, the average power consumption of

the ADC decreases at lower throughput rates. Figure 15

shows how as the throughput rate is reduced, the device

remains in its Power-Down state longer and the average

power consumption over time drops accordingly.

For example, if the AD7273/AD7274 is operated in a

continuous sampling mode with a throughput rate of

500KSPS and a SCLK of 52MHz (VDD= 3V), and the

device is placed in the Power-Down mode between

conversions, then the power consumption is calculated as

follows. The power dissipation during normal operation is

13.5 mW (VDD= 3V). If the power up time is one dummy

cycle, i.e. 333ns, and the remaining conversion time is

another cycle, i.e. 333ns, then the AD7273/AD7274 can

be said to dissipate 13.5mW for 666ns during each conver-

sion cycle.If the throughput rate is 500KSPS, the cycle

time is 2µs and the average power dissipated during each

cycle is (666/2000) x (13.5 mW)= 4.5mW.

Figure 15 shows the Power vs. Throughput Rate when

using the Power-Down mode between conversions at 3V.

The Power-Down mode is intended for use with

throughput rates of approximately TBD MSPS and under

as at higher sampling rates there is no power saving made

by using the Power-Down mode.

TBD

0

0

TITLE

Figure 15. Power vs Throughput

–18–

REV. PrB

Share Link: