AS3910-BQFP 查看數據表（PDF） - austriamicrosystems AG

零件编号

产品描述 (功能)

生产厂家

AS3910-BQFP

13.56 MHz RFID Reader IC, ISO-14443 A/B

austriamicrosystems AG 

AS3910

Data Sheet - Application Information

In case an interrupt from a certain source is not required it can be disabled by setting corresponding bit in the Mask Interrupt Register. In case of

masking a certain interrupt source the interrupt is not produced, but the source of interrupt bit is still set in Interrupt Register.

After reading the Interrupt Register the 13.56MHz clock coming from the oscillator is used to produce a reset signal which clears it and resets

INTR signal. Practically in all interrupt cases the oscillator is running when an interrupt is produced. The only exception is the interrupt in the

Initial NFC Target mode where only the Target Activation Detector is operating. In this case the interrupt is cleared with first SCLK rising edge

following reading of the Interrupt Register (an extra dummy CLK pulse during reading of the Interrupt Register or first SCLK pulse of the next SPI

command will do the job).

Table 8. Serial Peripheral Interface (4-wire Interface) Signal Lines

Name

Signal

Signal Level

Description

INTR

Digital Output

CMOS

Interrupt Output pin

8.9.9 FIFO Water Level and FIFO Status Register

The AS3910 contains a 32 byte FIFO. In case of transmitting the Control logic shifts data which was previously loaded by the external

microcontroller to the Framing Block and further to the Transmitter. During reception, the demodulated data is stored in the FIFO and the external

microcontroller can download received data once reception was terminated.

Transmit and receive capability the AS3910 is not limited by of the FIFO size due to a FIFO water level interrupt system. During transmission an

interrupt is sent (interrupt due to FIFO water level) when the content of data in the FIFO which still need to be sent is lower then the FIFO water

level for receive. The external microcontroller can now add more data in the FIFO. The same stands for receive mode. In case the number of

received bytes gets over the FIFO water level for receive an interrupt is sent to inform the external controller that data has to be downloaded from

FIFO.

The external controller has to serve the FIFO faster then data is transmitted or received. A general rule is that the SCLK frequency has to be at

least double then the actual data rate in receive or transmit.

There are two settings of the FIFO water level available for receive and transmit in Configuration Register 5 (#05).

After data is received the external microcontroller needs to know how long the receive data string was before downloading data from the FIFO:

This information is available in the FIFO Status Register (#09) which displays number of bytes in the FIFO which were not read out.

The FIFO Status Register also contains a FIFO overflow bit. This bit is set when during reception the external processor did not react on time

and more then 32 bytes were written in FIFO. The received data is of course lost in such a case.

8.10 Direct Commands

Table 9. Direct Commands

Code

000001

000010

000100

000101

000110

000111

001000

Command

Set default

Clear

Transmit with CRC

Transmit without CRC

Transmit REQA

Transmit WUPA

NFC transmit with Initial RF Collision

Avoidance

Comments

Puts the AS3910 in default state (same as after power-up)

Stops all activities and clears FIFO

Starts a transmit sequence using automatic CRC generation

Starts a transmit sequence without automatic CRC generation

Transmits REQA command (ISO-14443A mode only)

Transmits WUPA command (ISO-14443A mode only)

Equivalent to Transmit with CRC with additional RF Collision Avoidance

001001

001010

010000

010001

010010

010011

NFC transmit with Response RF Collision

Avoidance

Equivalent to Transmit with CRC with additional RF Collision Avoidance

NFC transmit with Response RF Collision

Avoidance with n=0

Equivalent to Transmit with CRC with additional RF Collision Avoidance

Mask receive data

Receive after this command is ignored

Unmask receive data

Receive data following this command is normally processed (this command has

priority over internal mask receive timer)

AD convert

A/D conversion of signal on AD_IN pin is performed, result is stored in A/D

Converter Output Register

Measure RF

RF amplitude is measured, result is stored in A/D Converter Output Register

www.austriamicrosystems.com/HF_RFID_Reader/AS3910

Revision 2.3

20 - 47

Share Link: